Alliance Laundry Systems HCN020HCF Instruction Manual Page 47
- Page / 70
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
Programming Control
45
F8237701
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
22. No Cycle Time Display “nCtd”
This option allows the owner to enable or disable
whether the cycle time will appear in the display.
How to Program No Cycle Time Display
1. Control must be in Manual Mode. Refer to
Entering the Manual Mode.
2. Press the Cold ( ) or the Delicate Cold ( )
keypad until “Prog” appears in the display. Press
the START (enter) keypad and “AtS” will appear
in the display.
3. Press the Cold ( ) or the Delicate Cold ( )
keypad to scroll through the programmable
options until “nCtd” appears in the display.
4. When “nCtd” appears in the display, press the
START (enter) keypad. The current No Cycle
Time Display status will appear in the display.
“on” = Option Enabled
“oFF” = Option Disabled (Default Setting)
5. Press the Cold ( ) or the Delicate Cold ( )
keypad to change the current status.
6. Press the START (enter) keypad when the
desired status appears in the display. The next
option, “PCtd”, will appear in the display.
NOTE: To program “PCtd” (Programmable Cycle
Time Display), refer to option 23. To program other
options, refer to the appropriate section.
How to Exit Programming Feature
Press the Delicate Warm (<) keypad until the control
returns to Ready Mode.
23. Programmable Cycle Time
Display “PCtd”
This option allows the owner to program the displayed
cycle time.
How to Program Programmable Cycle
Time Display
1. Control must be in Manual Mode. Refer to
Entering the Manual Mode.
2. Press the Cold ( ) or the Delicate Cold ( )
keypad until “Prog” appears in the display. Press
the START (enter) keypad and “AtS” will appear
in the display.
3. Press the Cold ( ) or the Delicate Cold ( )
keypad to scroll through the programmable
options until “PCtd” appears in the display.
4. When “PCtd” appears in the display, press the
START (enter) keypad. The current
Programmable Cycle Time Display status will
appear in the display.
“on” = Option Enabled
“oFF” = Option Disabled (Default Setting)
NOTE: Enabling this option will not change the
cycle time, only the display time for the user. Refer
to option “Cnin” in Cycle Programming to
program minutes to the cycle time display.
5. Press the Cold ( ) or the Delicate Cold ( )
keypad to change the current status.
6. Press the START (enter) keypad when the
desired status appears in the display. The next
option, “SdAd”, will appear in the display.
NOTE: To program “SdAd” (Slow Drain
Detection Adjust Value), refer to option 24. To
program other options, refer to the appropriate
section.
How to Exit Programming Feature
Press the Delicate Warm (<) keypad until the control
returns to Ready Mode.
>
<
>
<
>
<
>
<
>
<
>
<
- Washer-Extractor 1
- Table of 4
- Contents 4
- Model Identification 6
- Preliminary Information 7
- Control Identification 8
- Display Identification 9
- Machine Operation 10
- Changing Cycles 11
- Special Features 12
- Opening the Top Cover 13
- Entering the Manual Mode 14
- Programming Control 15
- F8237701 16
- Programming Flowcharts 18
- Manual Programming 19
- CHM1391R 20
- Figure 6 21
- Diagnostic 22
- 1. Cycle Vend Price “AtS” 23
- 2. Coin #1 Value “dEn1” 24
- 3. Coin #2 Value “dEn2” 25
- 4. Start Pulse Value “PLSE” 26
- 5. Start Pulse Mode “PLSn” 27
- 6. Available Type “AtyP” 28
- 7. Default Cycle “dCYC” 29
- 8. OPL Mode Enable/Disable 30
- 9. Audio Signal “AUd” 31
- How to Read Table 5 32
- 11. Cycle Programming “CyC-” 35
- Programming Fill Step 36
- Programming Supply Step 37
- Programming Agitate Step 38
- Programming Drain Step 38
- Programming Extract Step 39
- 14. IR Access (On/Off) “IrA” 42
- (Models with Heat) 42
- 17. Warm Water Temperature 43
- “Codn” (Models with Heat) 45
- 23. Programmable Cycle Time 47
- Display “PCtd” 47
- Value “SdAd” 48
- Collecting Audit Information 49
- Manual Reset 50
- Testing Machine and 51
- Electronic Control Functions 51
- Production Test Cycle 53
- To Exit Production Test Cycle 54
- Error Codes 56
- Rapid Advance Feature 59
- Clear Vend Feature 60
- Power Fail Recovery 61
- Communications Mode 62
- Default Cycles 63
Related products and manuals for Washing machines Alliance Laundry Systems HCN020HCF
(94 pages)© 2020, manymanuals.com. All rights reserved. | 0.419 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals