Alliance Laundry Systems HCN020HCF Instruction Manual Page 35
- Page / 70
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
Programming Control
33
F8237701
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
11. Cycle Programming “CyC-”
This option allows the owner to program different
aspects for various steps in each type of cycle. There
are eight cycles available for programming.
How to Enter Cycle Programming
1. Control must be in Manual Mode. Refer to
Entering the Manual Mode.
2. Press the Cold ( ) or the Delicate Cold ( )
keypad until “Prog” appears in the display. Press
the START (enter) keypad and “AtS” will appear
in the display.
3. Press the Cold ( ) or the Delicate Cold ( )
keypad to scroll through the programmable
options until “CyC-” appears in the display. Press
the START (enter) keypad and “CyC1” will
appear in the display.
4. Press the Cold ( ) or the Delicate Cold ( )
keypad to scroll through the eight cycles to
program. Press the START (enter) keypad when
the desired cycle appears in the display.
5. The first Cycle Programming option, “AgIt”, will
appear in the display.
NOTE: To program “AgIt” (Cycle Agitate),
continue to next option. To program other options,
press the Cold ( ) or the Delicate Cold ( ) keypad
and refer to the appropriate section.
How to Exit Programming Feature
Press the Delicate Warm (<) keypad until the control
returns to Ready Mode.
How to Program Cycle Agitate“AgIt”
This option allows the owner to program the cycle’s
agitation action and speed. These options apply to the
entire cycle.
1. Press the Cold ( ) or the Delicate Cold ( )
keypad to scroll through the programmable Cycle
Programming options until “AgIt” appears in the
display.
2. When “AgIt” appears in the display, press the
START (enter) keypad. The first Cycle Agitate
option will appear in the display.
3. Press the Cold ( ) or the Delicate Cold ( )
keypad to scroll through the programmable
options. Refer to Table 7.
4. Press the START (enter) keypad when the
desired programmable option appears in the
display. The current status will appear in the
display. Refer to Table 7.
Table 7
5. Press the Cold ( ) or the Delicate Cold ( )
keypad to change the current status.
6. Press the START (enter) keypad when the
desired status appears in the display. The next
Cycle Agitate option will appear in the display.
NOTE: To program “SEg1” (Cycle Segment 1)
press the Delicate Warm (<) keypad and continue
to next Cycle Programming option. To program
other options, press the Delicate Warm (<) keypad
and refer to the appropriate section.
How to Exit Programming Feature
Press the Delicate Warm (<) keypad until the control
returns to Ready Mode.
>
<
>
<
>
<
>
<
Final Spin
Step
Description Status
“
tyPE” Agitate Type 1 = Normal
2 = Gentle
“
ASPd” Agitate Speed
(VFD only)
“Lo” = Reduced Speed
“
rEg” = Normal Speed
>
<
>
<
>
<
- Washer-Extractor 1
- Table of 4
- Contents 4
- Model Identification 6
- Preliminary Information 7
- Control Identification 8
- Display Identification 9
- Machine Operation 10
- Changing Cycles 11
- Special Features 12
- Opening the Top Cover 13
- Entering the Manual Mode 14
- Programming Control 15
- F8237701 16
- Programming Flowcharts 18
- Manual Programming 19
- CHM1391R 20
- Figure 6 21
- Diagnostic 22
- 1. Cycle Vend Price “AtS” 23
- 2. Coin #1 Value “dEn1” 24
- 3. Coin #2 Value “dEn2” 25
- 4. Start Pulse Value “PLSE” 26
- 5. Start Pulse Mode “PLSn” 27
- 6. Available Type “AtyP” 28
- 7. Default Cycle “dCYC” 29
- 8. OPL Mode Enable/Disable 30
- 9. Audio Signal “AUd” 31
- How to Read Table 5 32
- 11. Cycle Programming “CyC-” 35
- Programming Fill Step 36
- Programming Supply Step 37
- Programming Agitate Step 38
- Programming Drain Step 38
- Programming Extract Step 39
- 14. IR Access (On/Off) “IrA” 42
- (Models with Heat) 42
- 17. Warm Water Temperature 43
- “Codn” (Models with Heat) 45
- 23. Programmable Cycle Time 47
- Display “PCtd” 47
- Value “SdAd” 48
- Collecting Audit Information 49
- Manual Reset 50
- Testing Machine and 51
- Electronic Control Functions 51
- Production Test Cycle 53
- To Exit Production Test Cycle 54
- Error Codes 56
- Rapid Advance Feature 59
- Clear Vend Feature 60
- Power Fail Recovery 61
- Communications Mode 62
- Default Cycles 63
Related products and manuals for Washing machines Alliance Laundry Systems HCN020HCF
(94 pages)© 2020, manymanuals.com. All rights reserved. | 1.396 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals