Alliance Laundry Systems HCN020HCF Instruction Manual Page 42
- Page / 70
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
Programming Control
F8237701
40
14. IR Access (On/Off) “IrA”
This option allows the owner to enable or disable
allowing the control to be read by an external device.
How to Program the IR Access (On/Off)
1. Control must be in Manual Mode. Refer to
Entering the Manual Mode.
2. Press the Cold ( ) or the Delicate Cold ( )
keypad until “Prog” appears in the display. Press
the START (enter) keypad and “AtS” will appear
in the display.
3. Press the Cold ( ) or the Delicate Cold ( )
keypad to scroll through the programmable
options until “IrA” appears in the display.
4. When “IrA” appears in the display, press the
START (enter) keypad. The current IR Access
status will appear in the display.
“on” = Option Enabled (Default setting)
“oFF” = Option Disabled
5. Press the Cold ( ) or the Delicate Cold ( )
keypad to change the current status.
6. Press the START (enter) keypad when the
desired status appears in the display. The next
option, “tFC” (Models with Heat) or “PtEn”
(Non-Heat Models), will appear in the display.
NOTE: For Models with Heat: To program “t FC”
(Fahrenheit/Celsius), refer to option 15. For Non-
Heat Models: To program “PtEn” (Production Test
Cycle [On/Off]), refer to
option 20. To program other options, refer to the
appropriate section.
How to Exit Programming Feature
Press the Delicate Warm (<) keypad until the control
returns to Ready Mode.
15. Fahrenheit/Celsius “t FC”
(Models with Heat)
This option allows the owner to set whether the
display will be shown in Fahrenheit or Celsius.
How to Program Fahrenheit/Celsius
1. Control must be in Manual Mode. Refer to
Entering the Manual Mode.
2. Press the Cold ( ) or the Delicate Cold ( )
keypad until “Prog” appears in the display. Press
the START (enter) keypad and “AtS” will appear
in the display.
3. Press the Cold ( ) or the Delicate Cold ( )
keypad to scroll through the programmable
options until “tFC” appears in the display.
4. When “tFC” appears in the display, press the
START (enter) keypad. A number will appear in
the display. This number (found below)
corresponds to the current Fahrenheit/Celsius
setting.
“CEL” = Celsius
“FAHr” = Fahrenheit (Default setting)
5. Press the Cold ( ) or the Delicate Cold ( )
keypad to increase or decrease the current
number to the desired number.
6. Press the START (enter) keypad when the correct
number of degrees appears in the display. The
new value is saved and the next option, “FH”,
will appear in the display.
NOTE: To program “FH” (Hot Water
Temperature), refer to option 16. To program other
options, refer to the appropriate section.
How to Exit Programming Feature
Press the Delicate Warm (<) keypad until the control
returns to Ready Mode.
>
<
>
<
>
<
>
<
>
<
>
<
- Washer-Extractor 1
- Table of 4
- Contents 4
- Model Identification 6
- Preliminary Information 7
- Control Identification 8
- Display Identification 9
- Machine Operation 10
- Changing Cycles 11
- Special Features 12
- Opening the Top Cover 13
- Entering the Manual Mode 14
- Programming Control 15
- F8237701 16
- Programming Flowcharts 18
- Manual Programming 19
- CHM1391R 20
- Figure 6 21
- Diagnostic 22
- 1. Cycle Vend Price “AtS” 23
- 2. Coin #1 Value “dEn1” 24
- 3. Coin #2 Value “dEn2” 25
- 4. Start Pulse Value “PLSE” 26
- 5. Start Pulse Mode “PLSn” 27
- 6. Available Type “AtyP” 28
- 7. Default Cycle “dCYC” 29
- 8. OPL Mode Enable/Disable 30
- 9. Audio Signal “AUd” 31
- How to Read Table 5 32
- 11. Cycle Programming “CyC-” 35
- Programming Fill Step 36
- Programming Supply Step 37
- Programming Agitate Step 38
- Programming Drain Step 38
- Programming Extract Step 39
- 14. IR Access (On/Off) “IrA” 42
- (Models with Heat) 42
- 17. Warm Water Temperature 43
- “Codn” (Models with Heat) 45
- 23. Programmable Cycle Time 47
- Display “PCtd” 47
- Value “SdAd” 48
- Collecting Audit Information 49
- Manual Reset 50
- Testing Machine and 51
- Electronic Control Functions 51
- Production Test Cycle 53
- To Exit Production Test Cycle 54
- Error Codes 56
- Rapid Advance Feature 59
- Clear Vend Feature 60
- Power Fail Recovery 61
- Communications Mode 62
- Default Cycles 63
Related products and manuals for Washing machines Alliance Laundry Systems HCN020HCF
(94 pages)© 2020, manymanuals.com. All rights reserved. | 0.306 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals