Alliance Laundry Systems HCN020HCF Instruction Manual Page 36
- Page / 70
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
Programming Control
F8237701
34
How to Program Cycle Segment “SEg1”
There are eight programmable cycle segments. Within
each segment, there are several programmable options.
1. Press the Cold ( ) or the Delicate Cold ( )
keypad to scroll through the eight programmable
Cycle Segments until the desired segment
appears in the display.
2. When the desired segment appears in the display,
press the START (enter) keypad. “SgEn”
(Segment Enable/Disable) will appear in the
display.
3. Press the Cold ( ) or the Delicate Cold ( )
keypad to scroll through the Cycle Segment
programmable options.
NOTE: If the Segment Enable/Disable is
programmed “oFF”, the other Cycle Segment
programming options can’t be accessed.
4. Press the START (enter) keypad when the
desired Cycle Segment programmable option
appears in the display.
Programming Segment Enable/Disable
1. When “SgEn” appears in the display, press the
START (enter) keypad. The current Segment
Enable/Disable status will appear in the display.
“on” = Segment is enabled
“oFF”= Segment is disabled
2. Press the Cold ( ) or the Delicate Cold ( )
keypad to change the current status.
NOTE: If the Segment Enable/Disable is
programmed “oFF”, the other Cycle Segment
programming options can’t be accessed.
3. Press the START (enter) keypad when the
desired status appears in the display. The next
Cycle Segment option, “FILL”, will appear in the
display.
NOTE: To program “FILL” (Fill Step), continue to
next Cycle Segment option. To program other
options, press the Cold ( ) or the Delicate Cold ( )
keypad and refer to the appropriate section.
How to Exit Programming Feature
Press the Delicate Warm (<) keypad until the control
returns to Ready Mode.
Programming Fill Step
1. When “FILL” appears in the display, press the
START (enter) keypad. The first Fill step
programming option will appear in the display.
2. Press the Cold ( ) or the Delicate Cold ( )
keypad to scroll through the programmable Fill
step options. Refer to Table 8.
NOTE: Fill Step “FLEn” must be enabled to scroll
through all Fill Step options.
3. Press the START (enter) keypad when the
desired option appears in the display. The current
status will appear in the display. Refer to Table 8.
4. Press the Cold ( ) or the Delicate Cold ( )
keypad to change the current status.
5. Press the START (enter) keypad when the
desired status appears in the display. The next
Fill step option will appear in the display.
NOTE: To program “SUPL” (Supply Step),
continue to next Cycle Segment option. To program
other options, press the Cold ( ) or the Delicate
Cold ( ) keypad and refer to the appropriate
section.
How to Exit Programming Feature
Press the Delicate Warm (<) keypad until the control
returns to Ready Mode.
>
<
>
<
>
<
>
<
Fill Step Description Status
“
FLEn” Fill Step
Enable/Disable
“on”/“oFF”
“
FLEU” Fill Level “HI” = high level
“nEd” = medium level
“Lo” = low level
“
tEnP” Fill Temperature “CoLd” = Cold
“UArn” = Warm
“Hot” = Hot
Table 8
>
<
>
<
>
<
- Washer-Extractor 1
- Table of 4
- Contents 4
- Model Identification 6
- Preliminary Information 7
- Control Identification 8
- Display Identification 9
- Machine Operation 10
- Changing Cycles 11
- Special Features 12
- Opening the Top Cover 13
- Entering the Manual Mode 14
- Programming Control 15
- F8237701 16
- Programming Flowcharts 18
- Manual Programming 19
- CHM1391R 20
- Figure 6 21
- Diagnostic 22
- 1. Cycle Vend Price “AtS” 23
- 2. Coin #1 Value “dEn1” 24
- 3. Coin #2 Value “dEn2” 25
- 4. Start Pulse Value “PLSE” 26
- 5. Start Pulse Mode “PLSn” 27
- 6. Available Type “AtyP” 28
- 7. Default Cycle “dCYC” 29
- 8. OPL Mode Enable/Disable 30
- 9. Audio Signal “AUd” 31
- How to Read Table 5 32
- 11. Cycle Programming “CyC-” 35
- Programming Fill Step 36
- Programming Supply Step 37
- Programming Agitate Step 38
- Programming Drain Step 38
- Programming Extract Step 39
- 14. IR Access (On/Off) “IrA” 42
- (Models with Heat) 42
- 17. Warm Water Temperature 43
- “Codn” (Models with Heat) 45
- 23. Programmable Cycle Time 47
- Display “PCtd” 47
- Value “SdAd” 48
- Collecting Audit Information 49
- Manual Reset 50
- Testing Machine and 51
- Electronic Control Functions 51
- Production Test Cycle 53
- To Exit Production Test Cycle 54
- Error Codes 56
- Rapid Advance Feature 59
- Clear Vend Feature 60
- Power Fail Recovery 61
- Communications Mode 62
- Default Cycles 63
Related products and manuals for Washing machines Alliance Laundry Systems HCN020HCF
(94 pages)© 2020, manymanuals.com. All rights reserved. | 1.925 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals