Alliance Laundry Systems HCN020HCF Instruction Manual Page 56
- Page / 70
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
F8237701
54
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
Error Codes
Following is a list of possible error codes for an
electronic control. Errors beginning with “EI” refer to
external device Infra-red communication errors. All
other errors refer to machine errors.
Display Description
Cause/
Corrective Action
EI01
Transmission Failure Communication failure. Re-aim external device and try
again.
EI02
Time-out Error Communication failure. Re-aim external device and try
again.
EI03
Invalid Command Code Communication successful, but the command was not
valid for this machine type, or the control could not
perform the command in its current mode of operation.
Ensure data is for current machine type and control is in
correct mode.
EI04
Expecting Upload Request Communication failure. Re-aim external device and try
again.
EI05
Invalid or Out-of-Range Data The value in at least one of the programming options is
invalid or out of range. Recheck the programming
option’s value and try again.
EI09
CRC-16 Error Communication failure. Re-aim external device and try
again.
EI0A
Framing Error Communication error. Re-aim external device and try
again.
EI0C
Time-out Exceeded Communication error. Re-aim external device and try
again.
EI0E
Encryption Error Communication error. Re-aim external device and try
again. If the problem persists, check that the security
code is correct.
EI0F
Infra-red Disabled Communication failure or infra-red is disabled.
Manually enable infra-red on control or re-aim external
device and try again.
E FL
Fill Error Programmed water level not reached within 10 minutes
(or other programmed length of time) in any fill agitate
cycle. End cycle. Power down machine to clear.
E SP
SPI Communications Error Front End control cannot communicate with output
board. Power down the machine, power up and try
again.
E dL
Door Lock Error Door does not lock immeadiately upon closing (open
and reclose door) or doesn’t unlock 5 seconds after cycle
completion. Power down machine and retry.
Table 17 (continued)
- Washer-Extractor 1
- Table of 4
- Contents 4
- Model Identification 6
- Preliminary Information 7
- Control Identification 8
- Display Identification 9
- Machine Operation 10
- Changing Cycles 11
- Special Features 12
- Opening the Top Cover 13
- Entering the Manual Mode 14
- Programming Control 15
- F8237701 16
- Programming Flowcharts 18
- Manual Programming 19
- CHM1391R 20
- Figure 6 21
- Diagnostic 22
- 1. Cycle Vend Price “AtS” 23
- 2. Coin #1 Value “dEn1” 24
- 3. Coin #2 Value “dEn2” 25
- 4. Start Pulse Value “PLSE” 26
- 5. Start Pulse Mode “PLSn” 27
- 6. Available Type “AtyP” 28
- 7. Default Cycle “dCYC” 29
- 8. OPL Mode Enable/Disable 30
- 9. Audio Signal “AUd” 31
- How to Read Table 5 32
- 11. Cycle Programming “CyC-” 35
- Programming Fill Step 36
- Programming Supply Step 37
- Programming Agitate Step 38
- Programming Drain Step 38
- Programming Extract Step 39
- 14. IR Access (On/Off) “IrA” 42
- (Models with Heat) 42
- 17. Warm Water Temperature 43
- “Codn” (Models with Heat) 45
- 23. Programmable Cycle Time 47
- Display “PCtd” 47
- Value “SdAd” 48
- Collecting Audit Information 49
- Manual Reset 50
- Testing Machine and 51
- Electronic Control Functions 51
- Production Test Cycle 53
- To Exit Production Test Cycle 54
- Error Codes 56
- Rapid Advance Feature 59
- Clear Vend Feature 60
- Power Fail Recovery 61
- Communications Mode 62
- Default Cycles 63
Related products and manuals for Washing machines Alliance Laundry Systems HCN020HCF
(94 pages)LUXA2 TX-P1 manuály
Uživatelské manuály a uživatelské příručky pro Energetické banky LUXA2 TX-P1.
Poskytujeme 1 manuály pdf LUXA2 TX-P1 ke stažení zdarma podle typů dokumentů: Uživatelský manuál
Comments to this Manuals