Alliance Laundry Systems BU170S Service Manual Page 115
- Page / 120
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
70422201R1
113
LED OPL and UniLinc Troubleshooting
Reverse Motor Test “”
This option shows the reverse motor running.
To start test, control must be in the Testing Mode.
Refer to “How to Enter Testing Feature” at the
beginning of this section.
To enter, press the Start ( ) keypad. The display
will show “
” to indicate the reverse motor is
going to run.
The test must run for at least six seconds before it can
be exited and off for six seconds before the test can be
run again.
NOTE: This test does not count towards the total
machine run time operation.
To exit Reverse Motor Test, press the Back ( )
keypad. The control will return to the testing mode.
Rotation Sensor Test “”
This option shows the RPM of the tumble dryer
cylinder.
To start test, control must be in the Testing Mode.
Refer to “How to Enter Testing Feature” at the
beginning of this section.
To enter, press the Start keypad. The display will show
“
”. The display is updated every ten seconds.
The test must run for at least six seconds before it can
be exited and off for six seconds before the test can be
run again.
NOTE: This test does not count towards the total
machine run time operation.
To exit Rotation Sensor Test, press the Back ( )
keypad. The control will return to the testing mode.
Moisture Sensor Test (Shorted Test
Jumper) “ ”
This step is skipped if the control is not configured for
Moisture Sensing. When entering this test, the control
will show “
” while flashing the Start LED one
second on/one second off, allowing the user to short
the cylinder to the baffle (orange jumper). When the
Start key is pressed, this test step energizes the Fan
Motor Contactor and Forward Motor Contactor and
the control will show “
”. The moisture sensor
test is 30 seconds. During this 30 second period, the
control is continually monitoring the moisture sensor
input for the expected short circuit. If an intermittent
signal or high resistance is sensed before the 30
seconds expire, the test is terminated and the control
will show “
”, indicating that the test has
failed. At this time the user has the option to press the
Back ( ) keypad to return and run the test again. If the
control ran the whole test reading the expected
moisture sensor level and without an intermittent
signal or high resistance, “
” will be shown. If
either the loading or lint doors are opened during the
test, the control will reset the test step and allow it to
be run again. When the test is complete and result is
displayed, the control sounds a 5 second audio signal.
Press a key to advance to the next test step. If the
Up ( ) or Down ( ) keypad is pressed while the test
is in progress the control will toggle between displays
“
”, “
” and “
”. If the display is
left on “
” or “
” for 5 seconds the
control will revert to showing “
”.
Moisture Sensor Test (Resistance Test
Jumper) “ ”
This step is skipped if the control is not configured for
Moisture Sensing. When entering this test, the control
will show “
” while flashing the Start key LED
one second on/one second off, allowing the user to
place the 510k Ohm resistor between the cylinder and
the baffle (black jumper) which simulates an expected
moisture sensor level. When the Start keypad is
pressed, this step energizes the Fan Motor Contactor
and Forward Motor Contactor and the control will
show “
”. The moisture sensor test is 30
seconds. During this 30 second period, the control is
continually monitoring the moisture sensor input for
the expected moisture sensor level. If an intermittent
signal or unexpected resistance is sensed before the
time expires, the test is terminated and the control will
show “
”, indicating that the test has failed. At
this time, the user has the option to press the Back ( )
keypad to return and run the test again. If the control
ran the test reading the expected moisture sensor level
and without an inttermittent signal or unexpected
resistance, “
” will be shown. If either the
loading or lint doors are opened during the test, the
control will reset the test step and allow it to be run
again. When the test is complete and result is
displayed, the control sounds a 5 second audio signal.
Press a key to advance to the next test step. If the
Up ( ) or Down ( ) keypad is pressed while the test
is in progress the control will toggle between
“
”, “
” and “
”. If the display is
left on “
” or “
” for 5 seconds the
control will revert to showing “
”.
- STRIAL TUMBLE DRYERS 1
- Table of 3
- Contents 3
- 70422101R1 4
- Section 1 5
- Safety Information 5
- Safety Warnings and Decals 7
- Tumblers 7
- Section 2 8
- Introduction 8
- Customer Service 10
- Serial Plate Location 10
- How a Tumble Dryer Works 11
- Operation 12
- Temperature Sensor 13
- Modes of Operation 14
- Section 3 15
- Troubleshooting 15
- 1. Motor Does Not Start 16
- 4. Motor Does Not Stop 19
- 6. No Heat Condition 21
- 7. Gas Burner Does Not Ignite 22
- 12.Clothes Do Not Dry 27
- 13.Tumble Dryer Overheating 28
- TMB2357S 34
- TMB2319S 35
- TMB2368S 36
- 21.Cylinder Is “Stained” 39
- Section 4 40
- Call the fire department 41
- TMB2199N 44
- SUPPRESSION 45
- Section 5 46
- Adjustments 46
- 27.Airflow Switch 47
- Pound Models) 47
- 30.Belt Drive 48
- 31.Cylinder Clearance 49
- TMB1786S 50
- 32.Drive Belt Tension 51
- 33.Fan Belt Tension 52
- Section 6 53
- 34.Control Has No Display 54
- 36.Motor Will Not Start/Run 58
- 37.Unit Will Not Heat – Gas 60
- 38.Error Codes 63
- Section 7 64
- 39.Control Has No Display 65
- 40.Door Open Indicator 67
- 41.Motor Will Not Start/Run 70
- 43.Error Codes 75
- Section 8 76
- Is there line voltage 77
- TMB2387S 79
- 45.No Drive Motor Rotation 80
- LED OPL Error Display: E Cab 83
- Is there 24 volts AC 85
- 48.Airflow Errors 87
- LED OPL Error Display: E FnCs 89
- 50.Close Door Indication 91
- 51.Moisture Sensor Error 93
- Figure 9 95
- Figure 10 96
- (Refer to Figure 11) 97
- Figure 12 98
- Machine Basket Removed 99
- Figure 13 100
- 58.Fan Motor Contactor Error 101
- TMB2383S 102
- 59.Rotation Sensor Error 103
- Rotation Sensor Error 104
- 60.Shorted or Open Thermistor 105
- Shorted or Open Thermistor 106
- SEE VOLTAGE 107
- OPTION DIAGRAM 107
- PROGRAMMING DIP SWITCHES 108
- (SEE INSTALLATION MANUAL 108
- FOR SWITCH DETAILS.) 108
- 63.Electronic Control Testing 109
- 70422201R1 110
- Diagnostic Test Descriptions 111
- Production Test Cycle 116
- 64.Diagnostic Testing 117
- Diagnostic Menu 117
- Test Menu 117
- Test Cycle Chart 118
- Inputs Outputs Menu 119
- Alarms Menus 120
- Machine ID Menu 120
Related products and manuals for Electric laundry dryers Alliance Laundry Systems BU170S
(23 pages)
(136 pages)
(74 pages)© 2020, manymanuals.com. All rights reserved. | 3.023 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals