Alliance Laundry Systems SCU020JLF Instruction Manual Page 78
- Page / 109
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
Programming Control
F8238301
76
How to Program Special Vend A Perm
Press/60C Vend Price “SA15”
This option allows the owner to set the vend price for a
PERM PRESS/60C wash in Special Vend A. The
corresponding LED will be lit while programming.
1. Press the NORMAL/40C ( ) or the PERM
PRESS/40C ( ) keypad to scroll through the
programmable Special Vend A options until
“SA15” appears in the display.
2. When “SA15” appears in the display, press the
START (enter) keypad. There are five digits in
the Special Vend A Perm Press/60C Vend Price.
The fifth digit will appear in the display and will
flash one (1) second on and one (1) second off.
Refer to Figure 19.
NOTE: If the vend price is $100.00 or more, the
fifth digit is “1-6”. If the vend price is $99.99 or
less, the fifth digit is “0”.
Figure 19
3. Press the NORMAL/40C ( ) or the PERM
PRESS/40C ( ) keypad to increase or decrease
the value of the fifth digit.
NOTE: The vend price can be set from 0 to 65,535.
4. Press the START (enter) keypad to enter the fifth
digit and display remaining four digits. The
active digit will flash one (1) second on and one
(1) second off.
NOTE: To go back to the current programmable
Special Vend A option without changing the value
of the active digit, press the PERM PRESS/60C (<)
keypad.
5. Press the NORMAL/40C ( ) or the PERM
PRESS/40C ( ) keypad to increase or decrease
the value of the active digit and the START
keypad to enter the value of the digit and advance
to the next digit.
6. Press the START (enter) keypad with the last
active digit. The next Special Vend A option,
“SA16”, will appear in the display.
NOTE: To program “SA16” (Special Vend A Perm
Press/40C Vend Price), continue to next Special
Vend A option. To program other options, press the
PERM PRESS/60C (<) keypad and refer to the
appropriate section.
How to Exit Programming Feature
Press the PERM PRESS/60C (<) keypad until the
control returns to Ready Mode.
CHM507R
>
<
>
<
>
<
- Washer-Extractor 1
- Table of 4
- Contents 4
- Model Identification 6
- Preliminary Information 7
- Control Identification 8
- Display Identification 9
- Machine Operation 10
- Changing Cycles 11
- Special Features 12
- Special Vend 13
- OPL Mode 13
- Opening the Top Cover 14
- Entering the Manual Mode 15
- Programming Control 16
- #3 /Supply #2 17
- F8238301 18
- Programming Flowcharts 21
- Manual Programming 22
- Diagnostic 27
- Figure 3 28
- 2. Coin #1 Value “dEn1” 29
- 3. Coin #2 Value “dEn2” 30
- 4. Start Pulse Value “PLSE” 31
- 5. Start Pulse Mode “PLSn” 32
- 6. Available Type “AtyP” 33
- 7. Default Cycle “dCYC” 34
- 9. Audio Signal “AUd” 36
- How to Read Table 5 37
- 12. Cycle Programming “CyC-” 43
- Programming Fill Step 44
- Programming Supply Step 45
- Programming Agitate Step 46
- Programming Drain Step 46
- Programming Extract Step 47
- (Models with Heat) 50
- 18. Warm Water Temperature 51
- “Codn” (Models with Heat) 52
- Disabled) “PtEn” 53
- 22. Manual Rapid Advance 53
- (Enabled/Disabled) “rAEn” 53
- 24. Programmable Cycle Time 54
- Display “PCtd” 54
- Value “SdAd” 55
- Disabled) “SPAU” 55
- Figure 7 56
- Figure 8 57
- Figure 9 58
- Figure 10 59
- Vend Price 60
- Figure 12 61
- Figure 13 62
- Figure 14 63
- Enable “SA01” 65
- How to Read Table 14 66
- 90C Vend Price “SA11” 74
- 60C Vend Price “SA12” 75
- 40C Vend Price “SA13” 76
- Press/90C Vend Price “SA14” 77
- Press/60C Vend Price “SA15” 78
- Press/40C Vend Price “SA16” 79
- Press/70C Vend Price “SA17” 80
- Press/50C Vend Price “SA18” 81
- 30C Vend Price “SA19” 82
- 37. Low Water Level “FLo” 84
- 38. Medium Water Level “FnEd” 84
- 39. High Water Level “FHI” 85
- Collecting Audit Information 87
- Manual Reset 88
- Testing Machine and 89
- Electronic Control Functions 89
- Production Test Cycle 91
- #3 or Compartment 92
- #3 Cold Fill 92
- Error Codes 94
- Table 21 (continued) 95
- Rapid Advance Feature 98
- Clear Vend Feature 99
- Power Fail Recovery 100
- Communications Mode 101
- Default Cycles 102
Related products and manuals for Washing machines Alliance Laundry Systems SCU020JLF
(24 pages)
(36 pages)
(82 pages)© 2020, manymanuals.com. All rights reserved. | 0.156 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals