Alliance Laundry Systems SCU020JLF Instruction Manual Page 22
- Page / 109
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
Programming Control
F8238301
20
Manual Programming
“Prog” Enter Program Mode
“AtS1” - Set vend price for Normal/90° C wash.
“dEn1” - Set value for the #1 coin entered.
“dEn2” - Set value for the #2 coin entered.
“AUd” - Program when the signal will sound.
“Err-” - Turn on/off certain errors in control.
“PLSE” - Program the value of the Start
Pulse.
“PLSn” - Program the Start Pulse Input for
one pulse or multiple pulses.
“E Fl” - Fill Error
“CEr-” - Coin Error Parameters
“E dr” - Drain Error
“E Ub” - Unbalance Error (VFD only)
“E Sd” - Slow Drain Detection
“FILL” - Program fill step options
“LEr-” - Leak Detection
“E oP” - Open Thermistor Error
(Models with Heat)
“E SH” - Shorted Thermistor Error
(Models with Heat)
“AtyP” - Program when control provides an
available output for card and central pay.
“dCYC” - Set the default cycle and
temperature.
“oPL” - Enable/disable OPL Mode in which
no vend price needs to satisfied to operate
machine.
“CArd” - Program whether the display is
controlled by machine’s electronic control or
the card reader.
“CyC-” - Program aspects for the various
steps in each type of cycle. There are (9)
cycles available for programming.
(continued)
“SEg1” - Program options for each
segment. There are (8) segments
available for programming
“SgEn” - Segment Enabled/Disabled:
“on” = Enabled
“oFF” = Disabled
“tyPE” - Agitation Type:
1 = Normal
2 = Gentle
“ASPd” - Agitation Speed (VFD only):
“Lo” = Reduced Speed
“rEg” = Normal Speed
“AgIt” - Program the cycles agitation
action and speed
(continued)
“CEr1” - Coin Error
“CEr2” - Coin Error Penalty
““FLEn” - Fill Step Enable/Disable:
“on” = Enabled
“oFF” = Disabled
“FLEU” - Fill Level:
“HI” = High Level
“nEd” = Medium Level
“Lo” = Low Level
“tEnP” - Fill Temperature:
“CoLd” = Cold
“UArn” = Warm
“Hot” = Hot
(35°F - 194°F [2°C - 90°C])
“E Ht” - Heat Error (heater only)
“CEr3” - Coin Drops Header Present Error
“LEr1” - Water Leak Detection During
a Machine Cycle
“LEr2” - Water Leak Detection - Day
of Week
“LEr3” - Number of Cycles between
Leak Detection Test
CHM1334R
- Washer-Extractor 1
- Table of 4
- Contents 4
- Model Identification 6
- Preliminary Information 7
- Control Identification 8
- Display Identification 9
- Machine Operation 10
- Changing Cycles 11
- Special Features 12
- Special Vend 13
- OPL Mode 13
- Opening the Top Cover 14
- Entering the Manual Mode 15
- Programming Control 16
- #3 /Supply #2 17
- F8238301 18
- Programming Flowcharts 21
- Manual Programming 22
- Diagnostic 27
- Figure 3 28
- 2. Coin #1 Value “dEn1” 29
- 3. Coin #2 Value “dEn2” 30
- 4. Start Pulse Value “PLSE” 31
- 5. Start Pulse Mode “PLSn” 32
- 6. Available Type “AtyP” 33
- 7. Default Cycle “dCYC” 34
- 9. Audio Signal “AUd” 36
- How to Read Table 5 37
- 12. Cycle Programming “CyC-” 43
- Programming Fill Step 44
- Programming Supply Step 45
- Programming Agitate Step 46
- Programming Drain Step 46
- Programming Extract Step 47
- (Models with Heat) 50
- 18. Warm Water Temperature 51
- “Codn” (Models with Heat) 52
- Disabled) “PtEn” 53
- 22. Manual Rapid Advance 53
- (Enabled/Disabled) “rAEn” 53
- 24. Programmable Cycle Time 54
- Display “PCtd” 54
- Value “SdAd” 55
- Disabled) “SPAU” 55
- Figure 7 56
- Figure 8 57
- Figure 9 58
- Figure 10 59
- Vend Price 60
- Figure 12 61
- Figure 13 62
- Figure 14 63
- Enable “SA01” 65
- How to Read Table 14 66
- 90C Vend Price “SA11” 74
- 60C Vend Price “SA12” 75
- 40C Vend Price “SA13” 76
- Press/90C Vend Price “SA14” 77
- Press/60C Vend Price “SA15” 78
- Press/40C Vend Price “SA16” 79
- Press/70C Vend Price “SA17” 80
- Press/50C Vend Price “SA18” 81
- 30C Vend Price “SA19” 82
- 37. Low Water Level “FLo” 84
- 38. Medium Water Level “FnEd” 84
- 39. High Water Level “FHI” 85
- Collecting Audit Information 87
- Manual Reset 88
- Testing Machine and 89
- Electronic Control Functions 89
- Production Test Cycle 91
- #3 or Compartment 92
- #3 Cold Fill 92
- Error Codes 94
- Table 21 (continued) 95
- Rapid Advance Feature 98
- Clear Vend Feature 99
- Power Fail Recovery 100
- Communications Mode 101
- Default Cycles 102
Related products and manuals for Washing machines Alliance Laundry Systems SCU020JLF
(24 pages)
(36 pages)
(82 pages)© 2020, manymanuals.com. All rights reserved. | 0.147 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals