Alliance Laundry Systems SCU020JLF Instruction Manual Page 92
- Page / 109
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
Testing Machine and Electronic Control Functions
F8238301
90
Production Test Cycle Quick Reference Chart
Display Test Cycle Step Comments
“S xx” FEC Control Software
Ver s ion
xx is the software version number.
“o xx” Output Board Software
Ver s ion
xx is the software version number.
“Ct25” Control Type 2.5 is the Control type.
“COIn” Control Type Coin
“IntL” Control Type International
“drAn” Drain Type Gravity Drain
“tEnP” Temp Sensor Step skipped if not model with heat.
“HEAt” Heater Step skipped if not heater-equipped.
“L dC” Door Lock Type “L dC” for 24 VDC lock.
“droP” or “drCL” Door Status Door open or closed.
“drUL” or “drLo” Door Lock Status Door will lock.
“8.8.8.8.” + all LEDs Display Test All display elements are lit.
“PAxx” where xx = 1-3,
5-11
Keypad Test step Advance after all keypads are pressed.
“A xx” Top Cover Switch Test xx is either “CL” for closed or “oP” for open.
“U xx” Coin Vault Switch Test xx is either “CL” for closed or “oP” for open.
“CxCx” Coin Drop Test 1st x is number of Coin Drop #1 coins. 2nd x is number of Coin
Drop #2 coins.
“Cxxx” Machine Type/Size
“drxx” Drive Software Version
Number
xx is the drive software version number. Design 2 models only.
“dPxx” Drive Parameter Table
Ver s i on N um ber
xx is the drive parameter table version number. Design 2 models
only.
“dt x” Drive Type Value xx is the drive type value. Design 2 models only.
“HFIL” Hot Fill to Low Level All water outputs turned off when Low Level reached.
“CFIL” Cold Fill to Low Level All water outputs turned off when Low Level reached.
“bFIL
” Warm Fill to Low Level All water outputs turned off when Low Level reached.
“bFIH” Warm Fill to High Level All water outputs turned off when High Level reached.
“S1” for supply or
“C2Co” for
compartment
Supply #1 or Compartment
#2 Cold Fill
“S2” for supply or
“C2Ho” for
compartment
Supply #2 or Compartment
#2 Hot Fill
“S3” for supply or
“C3Co” for
compartment
Supply
#3 or Compartment
#3 Cold Fill
Table 20 (continued)
- Washer-Extractor 1
- Table of 4
- Contents 4
- Model Identification 6
- Preliminary Information 7
- Control Identification 8
- Display Identification 9
- Machine Operation 10
- Changing Cycles 11
- Special Features 12
- Special Vend 13
- OPL Mode 13
- Opening the Top Cover 14
- Entering the Manual Mode 15
- Programming Control 16
- #3 /Supply #2 17
- F8238301 18
- Programming Flowcharts 21
- Manual Programming 22
- Diagnostic 27
- Figure 3 28
- 2. Coin #1 Value “dEn1” 29
- 3. Coin #2 Value “dEn2” 30
- 4. Start Pulse Value “PLSE” 31
- 5. Start Pulse Mode “PLSn” 32
- 6. Available Type “AtyP” 33
- 7. Default Cycle “dCYC” 34
- 9. Audio Signal “AUd” 36
- How to Read Table 5 37
- 12. Cycle Programming “CyC-” 43
- Programming Fill Step 44
- Programming Supply Step 45
- Programming Agitate Step 46
- Programming Drain Step 46
- Programming Extract Step 47
- (Models with Heat) 50
- 18. Warm Water Temperature 51
- “Codn” (Models with Heat) 52
- Disabled) “PtEn” 53
- 22. Manual Rapid Advance 53
- (Enabled/Disabled) “rAEn” 53
- 24. Programmable Cycle Time 54
- Display “PCtd” 54
- Value “SdAd” 55
- Disabled) “SPAU” 55
- Figure 7 56
- Figure 8 57
- Figure 9 58
- Figure 10 59
- Vend Price 60
- Figure 12 61
- Figure 13 62
- Figure 14 63
- Enable “SA01” 65
- How to Read Table 14 66
- 90C Vend Price “SA11” 74
- 60C Vend Price “SA12” 75
- 40C Vend Price “SA13” 76
- Press/90C Vend Price “SA14” 77
- Press/60C Vend Price “SA15” 78
- Press/40C Vend Price “SA16” 79
- Press/70C Vend Price “SA17” 80
- Press/50C Vend Price “SA18” 81
- 30C Vend Price “SA19” 82
- 37. Low Water Level “FLo” 84
- 38. Medium Water Level “FnEd” 84
- 39. High Water Level “FHI” 85
- Collecting Audit Information 87
- Manual Reset 88
- Testing Machine and 89
- Electronic Control Functions 89
- Production Test Cycle 91
- #3 or Compartment 92
- #3 Cold Fill 92
- Error Codes 94
- Table 21 (continued) 95
- Rapid Advance Feature 98
- Clear Vend Feature 99
- Power Fail Recovery 100
- Communications Mode 101
- Default Cycles 102
Related products and manuals for Washing machines Alliance Laundry Systems SCU020JLF
(24 pages)
(36 pages)
(82 pages)© 2020, manymanuals.com. All rights reserved. | 0.466 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals