Alliance Laundry Systems SCU020JLF Instruction Manual Page 53
- Page / 109
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
Programming Control
51
F8238301
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
21. Production Test Cycle (Enabled/
Disabled) “PtEn”
This option allows the owner to enable or disable
access to the production test cycle. Refer to
Production Test Cycle section for more information.
How to Program the Production Test
Cycle (Enabled/Disabled)
1. Control must be in Manual Mode. Refer to
Entering the Manual Mode.
2. Press the NORMAL/40C ( ) or the PERM
PRESS/40C ( ) keypad until “Prog” appears in
the display. Press the START (enter) keypad and
“AtS1” will appear in the display.
3. Press the NORMAL/40C ( ) or the PERM
PRESS/40C ( ) keypad to scroll through the
programmable options until “PtEn” appears in
the display.
4. When “PtEn” appears in the display, press the
START (enter) keypad. The current Production
Test Cycle status will appear in the display.
“on” = Option Enabled (Default Setting)
“oFF” = Option Disabled
5. Press the NORMAL/40C ( ) or the PERM
PRESS/40C ( ) keypad to change the current
status.
6. Press the START (enter) keypad when the
desired status appears in the display. The next
option, “rAEn”, will appear in the display.
NOTE: To program “rAEn” (Manual Rapid
Advance [on/off]), refer to option 22. To program
other options, refer to the appropriate section.
How to Exit Programming Feature
Press the PERM PRESS/60C (<) keypad until the
control returns to Ready Mode.
22. Manual Rapid Advance
(Enabled/Disabled) “rAEn”
This option allows the owner to enable or disable the
rapid advance feature. Refer to Rapid Advance
Feature section for more information.
How to Program the Manual Rapid
Advance (Enabled/Disabled)
1. Control must be in Manual Mode. Refer to
Entering the Manual Mode.
2. Press the NORMAL/40C ( ) or the PERM
PRESS/40C ( ) keypad until “Prog” appears in
the display. Press the START (enter) keypad and
“AtS1” will appear in the display.
3. Press the NORMAL/40C ( ) or the PERM
PRESS/40C ( ) keypad to scroll through the
programmable options until “rAEn” appears in
the display.
4. When “rAEn” appears in the display, press the
START (enter) keypad. The current Manual
Rapid Advance status will appear in the display.
“on” = Option Enabled (Default Setting)
“oFF” = Option Disabled
5. Press the NORMAL/40C ( ) or the PERM
PRESS/40C ( ) keypad to change the current
status.
6. Press the START (enter) keypad when the
desired status appears in the display. The next
option, “nCtd”, will appear in the display.
NOTE: To program “nCtd” (No Cycle Time
Display), refer to option 23. To program other
options, refer to the appropriate section.
How to Exit Programming Feature
Press the PERM PRESS/60C (<) keypad until the
control returns to Ready Mode.
>
<
>
<
>
<
>
<
>
<
>
<
- Washer-Extractor 1
- Table of 4
- Contents 4
- Model Identification 6
- Preliminary Information 7
- Control Identification 8
- Display Identification 9
- Machine Operation 10
- Changing Cycles 11
- Special Features 12
- Special Vend 13
- OPL Mode 13
- Opening the Top Cover 14
- Entering the Manual Mode 15
- Programming Control 16
- #3 /Supply #2 17
- F8238301 18
- Programming Flowcharts 21
- Manual Programming 22
- Diagnostic 27
- Figure 3 28
- 2. Coin #1 Value “dEn1” 29
- 3. Coin #2 Value “dEn2” 30
- 4. Start Pulse Value “PLSE” 31
- 5. Start Pulse Mode “PLSn” 32
- 6. Available Type “AtyP” 33
- 7. Default Cycle “dCYC” 34
- 9. Audio Signal “AUd” 36
- How to Read Table 5 37
- 12. Cycle Programming “CyC-” 43
- Programming Fill Step 44
- Programming Supply Step 45
- Programming Agitate Step 46
- Programming Drain Step 46
- Programming Extract Step 47
- (Models with Heat) 50
- 18. Warm Water Temperature 51
- “Codn” (Models with Heat) 52
- Disabled) “PtEn” 53
- 22. Manual Rapid Advance 53
- (Enabled/Disabled) “rAEn” 53
- 24. Programmable Cycle Time 54
- Display “PCtd” 54
- Value “SdAd” 55
- Disabled) “SPAU” 55
- Figure 7 56
- Figure 8 57
- Figure 9 58
- Figure 10 59
- Vend Price 60
- Figure 12 61
- Figure 13 62
- Figure 14 63
- Enable “SA01” 65
- How to Read Table 14 66
- 90C Vend Price “SA11” 74
- 60C Vend Price “SA12” 75
- 40C Vend Price “SA13” 76
- Press/90C Vend Price “SA14” 77
- Press/60C Vend Price “SA15” 78
- Press/40C Vend Price “SA16” 79
- Press/70C Vend Price “SA17” 80
- Press/50C Vend Price “SA18” 81
- 30C Vend Price “SA19” 82
- 37. Low Water Level “FLo” 84
- 38. Medium Water Level “FnEd” 84
- 39. High Water Level “FHI” 85
- Collecting Audit Information 87
- Manual Reset 88
- Testing Machine and 89
- Electronic Control Functions 89
- Production Test Cycle 91
- #3 or Compartment 92
- #3 Cold Fill 92
- Error Codes 94
- Table 21 (continued) 95
- Rapid Advance Feature 98
- Clear Vend Feature 99
- Power Fail Recovery 100
- Communications Mode 101
- Default Cycles 102
Related products and manuals for Washing machines Alliance Laundry Systems SCU020JLF
(24 pages)
(36 pages)
(82 pages)© 2020, manymanuals.com. All rights reserved. | 0.465 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals