Alliance Laundry Systems SCU020JLF Instruction Manual Page 10
- Page / 109
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
F8238301
8
Machine Operation
Start Up
When power is applied to the machine, the control will
display its software version as “Sxx” (“xx” is the
version number) for one second. If the control was not
powered down during a running cycle, it will enter
Ready Mode, Partial Vend Mode or Start Mode.
Ready Mode
In this mode of operation the control indicates the
current selected cycle by lighting the LEDs. The full
current vend price for the cycle appears in the display.
To start the cycle, the user must satisfy the vend price
and then press the START keypad.
The user will be able to select a different cycle by
pressing a cycle pad when the machine is in Ready
Mode.
Partial Vend Mode
The control enters this mode when part of the vend
price has been entered, but not enough vend is entered
to satisfy the vend price. The control will display the
remaining vend price needed to start the cycle.
The user will be able to select a different cycle by
pressing a cycle pad when the machine is in Partial
Vend Mode.
Additional Vend Mode
The control enters this mode if a higher priced cycle is
selected while the machine is in Start Mode or Run
Mode, but before the first fill has completed. If the
vend price is not satisfied within one (1) minute, the
control will go back to the first selection and the cycle
will continue if it was paused. After the first fill, all
key presses will be ignored, allowing the machine to
go through the complete cycle.
Start Mode
The control enters this mode when the full vend price
is satisfied, the vend price is zero, the control is in
OPL Mode. The START pad LED will flash one (1)
second on and one (1) second off. If Start Mode is
entered because the vend price is satisfied or the
control is in OPL Mode, the display will show
“PUSH” for one (1) second, “Strt” for one (1) second
and the current cycle time for one (1) second. If Start
Mode is entered because the vend price is zero, the
display will show “FREE”. When first entering Start
Mode, a signal will sound for one (1) second on and
one (1) second off for 10 seconds if Signal for Start is
enabled.
After pressing the START keypad, the door will lock
and the cycle will begin.
Door Locking Mode
The control enters this mode after the START (enter)
keypad is pressed in Start Mode. The control stays in
Door Locking Mode until it confirms the door is
closed and locked.
Run Mode
The control enters this mode when a cycle is running.
The time remaining appears in the display, the status
LEDs are lit and the loading door is locked.
End of Cycle Mode
When a cycle is complete, the control will display “00”
until the machine door is opened, a key is pressed, or a
coin/card is entered. The display will revert back to Ready
Mode if door is opened or keypad is pressed. If vend is
entered, the control will change to Partial Vend Mode or
Start Mode.
Cycle Sequence
Upon the start of a cycle, the control will display the
total cycle time. The appropriate LEDs will light while
the machine passes through different cycle steps. Any
coin entered after the first fill cycle has been started
will be added to the total coin counter, but the user will
not be able to change cycles or water temperature.
Door Unlocking Mode
The control enters this mode after cycle has ended. The
control waits for confirmation that door is unlocked.
Once confirmation is received that door is unlocked,
control will enter End of Cycle Mode.
- Washer-Extractor 1
- Table of 4
- Contents 4
- Model Identification 6
- Preliminary Information 7
- Control Identification 8
- Display Identification 9
- Machine Operation 10
- Changing Cycles 11
- Special Features 12
- Special Vend 13
- OPL Mode 13
- Opening the Top Cover 14
- Entering the Manual Mode 15
- Programming Control 16
- #3 /Supply #2 17
- F8238301 18
- Programming Flowcharts 21
- Manual Programming 22
- Diagnostic 27
- Figure 3 28
- 2. Coin #1 Value “dEn1” 29
- 3. Coin #2 Value “dEn2” 30
- 4. Start Pulse Value “PLSE” 31
- 5. Start Pulse Mode “PLSn” 32
- 6. Available Type “AtyP” 33
- 7. Default Cycle “dCYC” 34
- 9. Audio Signal “AUd” 36
- How to Read Table 5 37
- 12. Cycle Programming “CyC-” 43
- Programming Fill Step 44
- Programming Supply Step 45
- Programming Agitate Step 46
- Programming Drain Step 46
- Programming Extract Step 47
- (Models with Heat) 50
- 18. Warm Water Temperature 51
- “Codn” (Models with Heat) 52
- Disabled) “PtEn” 53
- 22. Manual Rapid Advance 53
- (Enabled/Disabled) “rAEn” 53
- 24. Programmable Cycle Time 54
- Display “PCtd” 54
- Value “SdAd” 55
- Disabled) “SPAU” 55
- Figure 7 56
- Figure 8 57
- Figure 9 58
- Figure 10 59
- Vend Price 60
- Figure 12 61
- Figure 13 62
- Figure 14 63
- Enable “SA01” 65
- How to Read Table 14 66
- 90C Vend Price “SA11” 74
- 60C Vend Price “SA12” 75
- 40C Vend Price “SA13” 76
- Press/90C Vend Price “SA14” 77
- Press/60C Vend Price “SA15” 78
- Press/40C Vend Price “SA16” 79
- Press/70C Vend Price “SA17” 80
- Press/50C Vend Price “SA18” 81
- 30C Vend Price “SA19” 82
- 37. Low Water Level “FLo” 84
- 38. Medium Water Level “FnEd” 84
- 39. High Water Level “FHI” 85
- Collecting Audit Information 87
- Manual Reset 88
- Testing Machine and 89
- Electronic Control Functions 89
- Production Test Cycle 91
- #3 or Compartment 92
- #3 Cold Fill 92
- Error Codes 94
- Table 21 (continued) 95
- Rapid Advance Feature 98
- Clear Vend Feature 99
- Power Fail Recovery 100
- Communications Mode 101
- Default Cycles 102
Related products and manuals for Washing machines Alliance Laundry Systems SCU020JLF
(24 pages)
(36 pages)
(82 pages)© 2020, manymanuals.com. All rights reserved. | 0.329 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals