Alliance Laundry Systems SCU020JLF Instruction Manual Page 43
- Page / 109
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
Programming Control
41
F8238301
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
12. Cycle Programming “CyC-”
This option allows the owner to program different
aspects for various steps in each type of cycle. There
are nine cycles available for programming.
How to Enter Cycle Programming
1. Control must be in Manual Mode. Refer to
Entering the Manual Mode.
2. Press the NORMAL/40C ( ) or the PERM
PRESS/40C ( ) keypad until “Prog” appears in
the display. Press the START (enter) keypad and
“AtS1” will appear in the display.
3. Press the NORMAL/40C ( ) or the PERM
PRESS/40C ( ) keypad to scroll through the
programmable options until “CyC-” appears in
the display. Press the START (enter) keypad and
“CyC1” will appear in the display.
4. Press the NORMAL/40C ( ) or the PERM
PRESS/40C ( ) keypad to scroll through the nine
cycles to program. Press the START (enter)
keypad when the desired cycle appears in the
display.
5. The first Cycle Programming option, “AgIt”, will
appear in the display.
NOTE: To program “AgIt” (Cycle Agitate),
continue to next option. To program other options,
press the NORMAL/40C ( ) or the PERM PRESS/
40C ( ) keypads and refer to the appropriate
section.
How to Exit Programming Feature
Press the PERM PRESS/60C (<) keypad until the
control returns to Ready Mode.
How to Program Cycle Agitate“AgIt”
This option allows the owner to program the cycle’s
agitation action and speed. These options apply to the
entire cycle.
1. Press the NORMAL/40C ( ) or the PERM
PRESS/40C ( ) keypad to scroll through the
programmable Cycle Programming options until
“AgIt” appears in the display.
2. When “AgIt” appears in the display, press the
START (enter) keypad. The first Cycle Agitate
option will appear in the display.
3. Press the NORMAL/40C ( ) or the PERM
PRESS/40C ( ) keypad to scroll through the
programmable options. Refer to Table 8.
4. Press the START (enter) keypad when the
desired programmable option appears in the
display. The current status will appear in the
display. Refer to Table 8.
5. Press the NORMAL/40C ( ) or the PERM
PRESS/40C ( ) keypad to change the current
status.
6. Press the START (enter) keypad when the
desired status appears in the display. The next
Cycle Agitate option will appear in the display.
NOTE: To program “SEg1” (Cycle Segment 1)
press the PERM PRESS/60C (<) keypad and
continue to next Cycle Programming option. To
program other options, press the PERM PRESS/
60C (<) keypad and refer to the appropriate
section.
How to Exit Programming Feature
Press the PERM PRESS/60C (<) keypad until the
control returns to Ready Mode.
>
<
>
<
>
<
>
<
Final Spin
Step
Description Status
“tyPE” Agitate Type 1 = Normal
2 = Gentle
“ASPd” Agitate Speed
(VFD only)
“
Lo” = Reduced Speed
“
rEg” = Normal Speed
Table 8
>
<
>
<
>
<
- Washer-Extractor 1
- Table of 4
- Contents 4
- Model Identification 6
- Preliminary Information 7
- Control Identification 8
- Display Identification 9
- Machine Operation 10
- Changing Cycles 11
- Special Features 12
- Special Vend 13
- OPL Mode 13
- Opening the Top Cover 14
- Entering the Manual Mode 15
- Programming Control 16
- #3 /Supply #2 17
- F8238301 18
- Programming Flowcharts 21
- Manual Programming 22
- Diagnostic 27
- Figure 3 28
- 2. Coin #1 Value “dEn1” 29
- 3. Coin #2 Value “dEn2” 30
- 4. Start Pulse Value “PLSE” 31
- 5. Start Pulse Mode “PLSn” 32
- 6. Available Type “AtyP” 33
- 7. Default Cycle “dCYC” 34
- 9. Audio Signal “AUd” 36
- How to Read Table 5 37
- 12. Cycle Programming “CyC-” 43
- Programming Fill Step 44
- Programming Supply Step 45
- Programming Agitate Step 46
- Programming Drain Step 46
- Programming Extract Step 47
- (Models with Heat) 50
- 18. Warm Water Temperature 51
- “Codn” (Models with Heat) 52
- Disabled) “PtEn” 53
- 22. Manual Rapid Advance 53
- (Enabled/Disabled) “rAEn” 53
- 24. Programmable Cycle Time 54
- Display “PCtd” 54
- Value “SdAd” 55
- Disabled) “SPAU” 55
- Figure 7 56
- Figure 8 57
- Figure 9 58
- Figure 10 59
- Vend Price 60
- Figure 12 61
- Figure 13 62
- Figure 14 63
- Enable “SA01” 65
- How to Read Table 14 66
- 90C Vend Price “SA11” 74
- 60C Vend Price “SA12” 75
- 40C Vend Price “SA13” 76
- Press/90C Vend Price “SA14” 77
- Press/60C Vend Price “SA15” 78
- Press/40C Vend Price “SA16” 79
- Press/70C Vend Price “SA17” 80
- Press/50C Vend Price “SA18” 81
- 30C Vend Price “SA19” 82
- 37. Low Water Level “FLo” 84
- 38. Medium Water Level “FnEd” 84
- 39. High Water Level “FHI” 85
- Collecting Audit Information 87
- Manual Reset 88
- Testing Machine and 89
- Electronic Control Functions 89
- Production Test Cycle 91
- #3 or Compartment 92
- #3 Cold Fill 92
- Error Codes 94
- Table 21 (continued) 95
- Rapid Advance Feature 98
- Clear Vend Feature 99
- Power Fail Recovery 100
- Communications Mode 101
- Default Cycles 102
Related products and manuals for Washing machines Alliance Laundry Systems SCU020JLF
(24 pages)
(36 pages)
(82 pages)© 2020, manymanuals.com. All rights reserved. | 1.064 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals