Alliance Laundry Systems LTS99A*N1180 Service Manual Page 91
- Page / 126
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
801803 89
Section 5 Service Procedures
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
To reduce the risk of electric shock, fire, explosion, serious injury or death:
• Disconnect all electric power to the machine and accessories before servicing.
• Close gas shut-off valve to gas dryer before servicing.
• Never start machine with any guards/panels removed.
• Whenever ground wires are removed during servicing, these ground wires must be
reconnected to ensure that the machine is properly grounded.
• Washer motor not grounded! Disconnect electric power before servicing motor.
W502
WARNING
IMPORTANT: When installing lint filter, be sure to
install the filter with the words facing the front of
the dryer. If filter is installed backwards, lint will
accumulate in exhaust system, which can adversely
affect dryer performance.
e. Remove three screws holding the air duct to the
front bulkhead inside cylinder. Refer to
Figure 41.
f. Carefully lift air duct out of dryer.
IMPORTANT: When reassembling, be sure seal on
exhaust fan cover makes airtight seal on flange of
duct. Refer to Figure 40. If the seal is installed
improperly, the airflow through the exhaust system
will be restricted which can adversely affect dryer
performance.
71. DRYER MOTOR AND EXHAUST
ASSEMBLY
a. While supporting the access panel, remove two
screws from bottom edge of access panel. Refer
to Figure 27.
b. Gently lower the access panel to disengage
locators from bottom edge of front panel. Refer
to Figure 35.
c. Open loading door, remove screw, and lift filter
out of bulkhead.
d. Remove screws holding air duct to front
bulkhead (inside cylinder). Refer to Figure 41.
IMPORTANT: When reassembling, be sure seal on
exhaust fan cover makes airtight seal on flange of
duct. Refer to Figure 42. If the seal is installed
improperly, the airflow through the exhaust system
will be restricted, which can adversely affect dryer
performance.
e. Disconnect wires from thermostat.
NOTE: Refer to wiring diagram when rewiring
thermistor.
f. Remove screw holding ground wire to dryer
base. Refer to Figure 42.
g. Remove cylinder belt from idler and motor
pulleys. Refer to Figure 43.
h. Disengage motor wire harness terminal block
from motor switch by pressing in on the
movable locking tabs (located on each end of
the terminal block) and pulling away from
motor. Refer to Figures 46 and 47.
i. Remove two screws holding motor mounting
bracket to dryer base. Refer to Figure 42.
Figure 42
To reduce the risk of serious injury or death
by carbon monoxide and other gases in
gas dryers, carefully read and follow all
instructions given in this section.
W005
WARNING
Cover
Attaching
Screws
Thermostat
Motor
Mount
Attaching
Screws
D400SE1E
Ground
Wire
To reduce the risk of serious injury or death
by carbon monoxide and other gases in
gas dryers, carefully read and follow all
instructions given in this section.
W005
WARNING
- Homestyle 1
- Stacked Washer/ 1
- Table of Contents 3
- Section 6 – Adjustments 4
- Model Identification 5
- 4 801803 6
- Section 1 7
- Safety Information 7
- 6 801803 8
- Section 2 9
- Introduction 9
- 8 801803 10
- General (Dryer) 11
- General (Washer) 11
- Technical (Washer) 11
- 10 801803 12
- Section 3 13
- Troubleshooting 13
- 12 801803 14
- 14 801803 16
- POSSIBLE CAUSE TO CORRECT 16
- 16 801803 18
- 18 801803 20
- 20 801803 22
- 22 801803 24
- (NO RESPONSE TO START SWITCH) 26
- 26 801803 28
- 801803 27 29
- (DOOR LED FLASHING) 30
- 23. WASHER MOTOR WILL NOT RUN 32
- WASHER MOTOR WILL NOT RUN 33
- (WASH/DOOR LEDS FLASHING) 34
- Washer Overflows 36
- WASHER OVERFLOWS 37
- 26. PUMP DOES NOT OPERATE 38
- PUMP DOES NOT OPERATE 39
- 38 801803 40
- SERIAL COMMUNICATION ERROR 41
- 40 801803 42
- Section 4 43
- Grounding 43
- 42 801803 44
- Figure 2 44
- Figure 3 45
- 44 801803 46
- Figure 4 47
- 46 801803 48
- Figure 5 49
- 48 801803 50
- Section 5 51
- Service Procedures 51
- 50 801803 52
- Figure 7 53
- 52 801803 54
- Figure 8 55
- 54 801803 56
- Figure 9 56
- Figure 10 57
- 56 801803 58
- Figure 11 58
- Figure 12 59
- 58 801803 60
- Figure 13 61
- Figure 14 61
- 60 801803 62
- Figure 15 62
- Figure 16 62
- Figure 17 63
- 62 801803 64
- Figure 18 65
- 64 801803 66
- Section 5 Service Procedures 67
- 66 801803 68
- Figure 19 68
- 68 801803 70
- Figure 20 70
- 70 801803 72
- Figure 21 73
- Figure 22 73
- 72 801803 74
- Figure 23 74
- Figure 24 75
- 74 801803 76
- Figure 25 76
- Figure 26 76
- 76 801803 78
- Figure 27 79
- SWD1674S 80
- Figure 31 81
- 80 801803 82
- Figure 32 82
- Figure 33 83
- 82 801803 84
- Figure 34 84
- Figure 35 85
- 84 801803 86
- Figure 36 86
- Figure 37 87
- 86 801803 88
- Figure 38 88
- Figure 39 89
- 88 801803 90
- Figure 40 90
- Figure 41 90
- Figure 42 91
- 90 801803 92
- Figure 43 92
- Figure 44 92
- Figure 45 93
- Figure 46 93
- 92 801803 94
- Figure 47 94
- Figure 48 95
- Figure 49 95
- 94 801803 96
- Figure 50 96
- Figure 51 97
- 96 801803 98
- Figure 52 98
- 98 801803 100
- Figure 53 100
- Figure 54 101
- 100 801803 102
- Figure 55 103
- Figure 56 104
- 102 801803 104
- Figure 57 105
- 104 801803 106
- Section 6 107
- Adjustments 107
- 106 801803 108
- Figure 59 108
- Figure 60 109
- SHOWN CLOSED 110
- Figure 62 111
- 110 801803 112
- Figure 63 112
- Section 7 113
- Dryer Test Procedures 113
- Figure 65 115
- 801803 115 117
- 116 801803 118
- Figure 66 118
- Figure 67 119
- 118 801803 120
- Figure 68 120
- Secondary 121
- And Booster 121
- SILICON CARBIDE IGNITER AND 122
- BRACKET ASSEMBLY 122
- 801803 121 123
- 122 801803 124
- Section 8 125
- 124 801803 126
Related products and manuals for Washer dryers Alliance Laundry Systems LTS99A*N1180
(88 pages)
(8 pages)
(18 pages)© 2020, manymanuals.com. All rights reserved. | 0.266 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals