Alliance Laundry Systems 1336 Service Manual Page 94
- Page / 95
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
94 F238006
Section 5 Service Procedures
To reduce the risk of electrical shock, fire, explosion, serious injury or death:
• Disconnect electrical power to the washer-extractor before servicing it.
• Close the gas shut-off valve to the washer-extractor (when applicable) before servicing it.
• Never start the washer-extractor with any guards/panels removed.
• Whenever ground wires are removed during servicing, these ground wires must be
reconnected to ensure that the washer-extractor is properly grounded.
W461R1
WARNING
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
t. Torque the Front Bearing: Make sure that the
short 3mm Allen wrench is secured in the head
of the set screw. Alternately tighten the
mounting set screws in 1/2 turn increments
until they are tightened to 80in-lbs of torque.
The Allen wrench is designed to flex
approximately 3/4 inches when 80 in-lbs is
achieved.
u. Torque the Rear Bearing: Make sure that the
short 3mm Allen wrench is secured in the head
of the set screw. Alternately tighten the
mounting set screws in 1/2 turn increments
until they are tightened to 80in-lbs of torque.
The Allen wrench is designed to flex
approximately 3/4 inches when 80 in-lbs is
achieved.
v. Recheck each set screw and retighten them as
needed. No threads should be visible.
w. Check the up and down play of the basket. The
bearings are not correctly mounted if play
exists.
x. Apply methoxy sealant at the split of the
bearing sleeve.
NOTE: Make sure that the new cartridge seal has
0.125 inches of axial (spring pressure) movement in
it.
y. After the bearings are set, check to see if the
metal ring on the seal is against the nylon
retainer. If needed, slide the brass collar
forward until the ring comes into contact with
the nylon. This will set the correct seal spring
compression. Refer to Figure 35.
z. Tighten the brass collar to the shaft using the
three set screws located in the brass collar.
aa. Remove the retaining ring from the cartridge
seal using a screwdriver. Refer to Figure 35.
ab. Reinstall the pulley and the belt.
ac. Reinstall the door trim and shell band. Realign
them using the marks made in the previous step.
ad. Reinstall the door lock cover on the machine.
ae. Reconnect the spray rinse hose to the spray tube
assembly.
af. Reinstall all of the panels.
ag. Test the machine for leaks.
Figure 35
PHM277K
Retaining
Ring
- Washer-Extractor 1
- Table of Contents 2
- 2 F238006 3
- Section 1 4
- Safety Information 4
- Important Safety Instructions 5
- Section 1 Safety Information 6
- 6 F238006 7
- Section 2 8
- Introduction 8
- Model Identification 9
- Section 3 10
- Installation 10
- Electrical Installation 11
- Section 3 Installation 12
- 12 F238006 13
- Section 4 14
- Troubleshooting 14
- 14 F238006 15
- Section 4 Troubleshooting 16
- 16 F238006 17
- 18 F238006 19
- 20 F238006 21
- 3. NO FILL ANALYSIS 23
- 24 F238006 25
- 26 F238006 27
- 28 F238006 29
- 5. DOOR LOCK SWITCH ANALYSIS 31
- 32 F238006 33
- Door Lock Switch Analysis 33
- 6. NO FUSEBOARD FUNCTIONS 35
- 36 F238006 37
- A-B 1305 Control Logic 40
- A-B 1336 Control Logic 41
- 42 F238006 43
- 44 F238006 45
- 46 F238006 47
- 48 F238006 49
- 10. NO SPIN 51
- 11. FILL ALARM ANALYSIS 52
- 52 F238006 53
- 54 F238006 55
- 56 F238006 57
- 58 F238006 59
- 14. NO KEYPAD FUNCTIONS 60
- 15. DOOR UNLOCKING FUNCTION 61
- 62 F238006 63
- 64 F238006 65
- Section 5 67
- Service Procedures 67
- 68 F238006 68
- Figure 1 68
- Figure 2 69
- 70 F238006 70
- Figure 3 70
- Meter Lead Placement 70
- Test equipment required: 71
- Computer Test Procedure 71
- Section 5 Service Procedures 72
- 74 F238006 74
- Figure 4 74
- Computer Board and Keypad 74
- Figure 5 75
- TO INSERT AND REMOVE 76
- FLAT RIBBON CABLE 76
- RIBBON CABLE PLUG MUST 76
- BE ALIGNED WITH SOCKET 76
- Figure 8 77
- Clear Covers and R.C. Network 77
- Figure 9 77
- Four-Pin Connector 77
- 78 F238006 78
- Figure 10 78
- Interface Board 78
- Figure 11 79
- Temperature Calibration 79
- 80 F238006 80
- Removal and Installation 80
- Figure 12 80
- PHM1947S 81
- PHM1946S 82
- Deflection 83
- Span Length 83
- PHM1941S 85
- PHM1948S 85
- PHM1943S 86
- Figure 25 87
- Figure 26 87
- 88 F238006 88
- Figure 27 88
- Figure 28 88
- Figure 29 89
- PHM197K 90
- PHM198K 91
- 92 F238006 92
- Mounting Instructions 92
- Figure 34 93
- 94 F238006 94
- Figure 35 94
- Bearing Troubleshooting Tips 95
Related products and manuals for Washing machines Alliance Laundry Systems 1336
(99 pages)
(104 pages)
(68 pages)© 2020, manymanuals.com. All rights reserved. | 2.301 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals